FLATDEK® Ⅱ

flatdek-2
flatdek-2-draw-1

Colour Range

Topside – Standard COLORBOND® steel Underside – 80% Hi Gloss
Classic Cream™ Hi Gloss Classic Cream™
Surfmist® Hi Gloss Dover White
Classic Cream™ Hi Gloss Dover White
Paperbark® Hi Gloss Paperbark®
Wilderness® Hi Gloss Classic Cream™
Bluestone® Hi Gloss Classic Cream™

Product Description and Features

FLATDEK® Ⅱ is a modern long span cladding particularly well suited to many types of home improvement projects such as room additions, carports and awnings. The underside of FLATDEK® Ⅱ features clean un-interrupted lines, with an attractive gloss finish.

  • Pan-fixed roof sheeting for open sided awnings where high degree of weather tightness is not required
  • The top side finished in a limited range of COLORBOND® steel colours. The ceiling side is finished in either Classic Cream® or Paperbark® high gloss COLORBOND® steel.

Note

    • Available in Queensland only
    • May be used on roof pitches from as low as 2 degrees (1 in 30)

      Spanning Table

      The maximum recommended support spacings are based on testing in accordance with AS 1562.1-1992. Design and installation of sheet roof and wall cladding, and AS 4040.1-1992. Resistance to concentrated loads.**

      The pressure considered is based on a typical awning Cpn=-0.8 and Kl=1.5 adjacent to an enclosed structure.

      The tables are based on FLATDEK® Ⅱ fixed to supports of 1.0mm BMT minimum. For FLATDEK® Ⅱ awnings applications, the awning span is often governed by the capacity of the receiver channel and its connections. This must be considered in the design of any awning system.

      Depending on support spacings used, FLATDEK® Ⅱ can be installed as either a:

      • Light foot traffic roof (incidental maintenance foot traffic acceptable); or
      • No foot traffic roof (will not support the weight of a person walking on it), this considers resistance to wind pressure only.
      Spans for light foot traffic
      Maximum support spacings (mm)
      Span type Wind Classification to AS 4055 & BCA
      N1 (W28) N2 (W33) N3 (W41N) N4 (W50N)
      Single
      End
      Internal
      2400
      2800
      3200
      2400
      2800
      3200
      2400
      2800
      3200
      2400
      2800
      3200
      Spans for no foot traffic
      Maximum support spacings (mm)
      Span Type Wind classification to AS 4055
      N1 (W28) N2 (W33) N3 (W41N) N4 (W50N)
      Single
      End
      Internal
      Stiffened Overhangs
      5100*
      4800
      4800
      600
      5100*
      4800
      4800
      600
      4500
      3700
      4450
      450
      3300
      3000
      3500
      400

      Supports must be not less than 1mm BMT.
      * Spans of 5100mm may result in noticable deflections under maximum loads. When deflections need to be considered in designs, reduce these spans to 4800mm.

      flatdek-2-draw-2

      Availability

      NSW/ACT VIC TAS QLD NT SA WA
      Not Avail. Not Avail. Not Avail. Avail. Not Avail. Not Avail. Not Avail.

      Specifications

      engths

       

      Sheets are supplied custom cut.

      Material Specifications

      • COLORBOND® prepainted steel complying with AS/NZS 2728:Type 4, is made from zinc-aluminium alloy coated steel complying with AS1397-2001, G550 (550MPa minimum yield stress), AZ150 (150g/m2 minimum coating mass) or AZ200 (200g/m2 minimum coating mass), or
      • The base metal thickness is 0.42mm

      Schematic

      flatdek-2-draw-3